How to Assemble Computer (PC) Along The picture

Step

INSTALASI PC

s Along The picture Assemble PC Complete
 Security Safety (K3)Before assembling a PC there are a few tips to consider, including:1. Avoid assemble in a state of sweating, because the sweat would drip keperalatan chances are we raft without our knowledge, and then when we turned on the power supply and it caused short circuiting and can destroy the results of assemblies.2. Avoid holding or touching directly the existing foot possessor including chipset. Because it was feared the static electricity that owned our bodies will damage these components.
To prevent this, we have to ground-kan our body by holding the casing when the power is turned on or by wearing an antistatic wristband without having to hold the casing.3. At each stage of assembly before adding a new component, power supply should be turned off. Replacing the power supply components at the time of life will damage the components to be installed and other components.4. Do not forget to prepare the equipment and materials before starting the assembly, so that all assembly activities are not hampered the possibility of a lack of existing equipment.5. Avoid mounting components with rugged hard drive, as it may damage the hard drive.Tools and materialstool:1. Screwdriver Plus (+)2. Screwdriver Minus (-)3. Tang Taper (claw crocodile)4. Multimeter / Multitester5. Tweezers6. Anti Static BraceletMaterial :1. MotherboardThe motherboard is a motherboard or main circuit board in a computer, which contains an electronic circuit that serves as a processing center.2. ProcessorProcessor is the main component of most computers because it determines whether the poor performance of the computer (brain computer). Serves as a data processor within a computer system.Type of processor that is often used in assembling pc / computer itself is good and right for the game as well as usual there are 2 of Intel with the type of Pentium III, Pentium 4, dual core, quad core, Core i3, Core i5, Core i7 and AMD with the type Sempron , athlon, until phenom.3. Heatsink (Fan)Heatsink is the processor cooling fan and other components, because the temperature is very hot processor.4. Hard DriveHard drive is a hardware component that stores data and contain magnetic disk. Serves as data storage to improve computer performance.5. Memory (RAM)RAM (Random Access Memory) is Internal Memory, which serves to store data.6. Floppy Disk Drive (FDD)FDD is a storage device that serves to connect the data transfer, data readout or "write" data from a PC onto a diskette.7. CD / DVD DriveCD / DVD ROM drive is a storage device that serves to connect the data, data transfer, data readout or "write" data from a PC onto a CD / Cassette8. Graphic Card (VGA Card)Card VGA (Video Graphics Adapter) is a component that serves to translate the computer output to the monitor. For the graphic design process or playing video games, needed a high-powered graphics card.9. Sound CardSound Card is a device shaped slab of PCB and is able to process and produce sound. Tasked to support the voice functions in a multimedia PC.10. Power SupplyPower Supply is a computer device that serves to supply power to each part of the computer in order to run.11. Casing12. Keyboard & Mouse13. MonitorStep-by-step assemblyHere is a step-by-step assembly CPU.1. Place the motherboard on a flat place and do not forget to put a pedestal with a soft surface so that the motherboard is not scratched or broken pathway components.

 

 2. Replace the processor on the motherboard. Installation processor earned outside the casing in order to facilitate you in the installation of the processor. Installation processor tailored to the type of processor and the motherboard used.

 

 3. Once the processor is installed and then do the installation of the processor fan.

4. Install the RAM on the RAM slot available on the motherboard. Installation of RAM in the slot should follow the rules because if there is an error in the installation can create RAM and motherboard damaged or burned.

5. Prepare the chassis for the installation of all components that have been provided.

6. After you set up the chassis attach the power supply or power supply as shown below.

7. After that, enter the motherboard in the chassis slowly so that the motherboard is not damaged. At the time of the motherboard installation, note the mouse connector, keyboard, serial, VGA and sound to be attached to the panels contained in the casing properly.

8. Then bautlah motherboard with the stand so strong and does not shake.

9. In this example we use a motherboard that is equipped with VGA, Sound Card, and the LAN card is built into the motherboard. Components that has become one with the motherboard called a component ON BOARD.

10. After the install CD ROM on the shelf contained in the casing, by entering from the front.

11. Then bautlah CD ROM that was installed earlier invitation shelves so as not to jiggle. Then attach the power cable and a data cable or cables ATA CD ROM on the motherboard.

12. Install the hard drive on the shelf contained on the hard drive casing with slowly so as not to hit. Because components of this hard drive is prone tehadap shocks. Then bolt firmly so as not to shake.

13. Once the hard drive is installed and then plug the data cable or cables ATA hard drive on the motherboard and the hard disk itself.

14. Connect the power supply in place contained in the motherboard. If the installation is wrong then it will result in fatal damage to the motherboard.

15. Then plug the power connector / restart / hdd lad / power lad and the other connector pad located on the motherboard as shown below.

16. Once all the components have been installed and install a casing cover properly.

The assembly is completed then we should test whether successful or not. Attach the monitor to the VGA port cable then monitor and CPU power to the power switch, then turn it on when the computer can boot the managed assembly. If it can not boot means the assembly is not perfect, it must be refined first if you later want to install the Operating System it by way of a check back all the components that are installed whether it is correct or not